withstand voltage isolation resistance i/p-o/p:3.75kvac i/p-fg:1.88kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc / 25 / 70% rh constant current region note.4 hlg-185h-12 a specification model dc voltage rated current rated power output voltage adj. range note.6 current adj. range line regulation load regulation setup, rise time note.8 hold up time (typ.) voltage range note.5 frequency range power factor efficiency (typ.) ac current input inrush current( .) typ leakage current safety standards note.7 harmonic current ems immunity working temp. working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing over current note.4 over voltage over temperature can be adjusted by internal potential meter or through output cable 2500ms, 80ms / 115vac ; b type 2500ms, 200ms at 95% load 230vac / 115vac at full load 230vac 16ms at full load 230vac / 115vac 90 ~ 305vac 127 ~ 431vdc 47 ~ 63hz pf 0.95/230vac pf 0.98/115vac at full load and rated output voltage pf 0.9 at 50 ~ 100% load 1.8a / 115vac 0.8a / 230vac 0.7a / 277vac 2.1a / 115vac 0.9a / 230vac 0.8a / 277vac cold start 75a/230vac <0.75ma / 277vac 95 ~ 108% protection type : constant current limiting, recovers automatical ly after fault condition is removed compliance to en55015 , en55022 (cispr22) class b compliance to en61000-3-2 class c ( 50% load) ; en61000-3-3 compliance to en61000-4-2,3,4,5,6,8,11; env50204, en61547, en 55024, heavy industry level (surge 4kv), criteria a -40 ~ +60 @ full load ; +70 @ 60% load (refer to derating curve) 20 ~ 95% rh non-condensing -40 ~ +80 , 10 ~ 95% rh 0.03%/ (0 ~ 50 ) 10 ~ 500hz, 5g 12min./1cycle, period for 72min. each along x, y, z axes 192.2 khrs min. mil-hdbk-217f (25 ) 228*68*38.8mm (l*w*h) 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. constant current operation region is within 50% ~100% rated output vol tage. this is the suitable operation region for led related application s, but please reconfirm special electrical requirements for some specific syste m design. 5. derating may be needed under low input voltages. please check the static c haracteristics for more details. 6. type a only. 7. safety and emc design refer to en60598-1, cns15233, gb7000.1, fcc part 18. 8. length of set up time is measured at cold first start. turning on/off the powe r supply may lead to increase of the set up time. 9. the power supply is considered as a component that will be operated in combi nation with final equipment. since emc performance will be affected by th e complete installation, the final equipment manufacturers must re- qualify emc directive on the complete installation again. 10. refer to warranty statement. 1.15kg; 12pcs/14.8kg/0.76cuft 185w single output switching power supply universal ac input / full range (up to 305vac)built-in active pfc function protections: short circuit / overload / over voltage / over temperature cooling by free air convection ocp point adjustable through output cable or internal potential meter ip67 / ip65 design for indoor or outdoor installations three in one dimming function (1~10vdc or pwm signal or resistor) suitable for led lighting and street lighting applications compliance to worldwide safety regulations for lighting 5 years warranty suitable for dry / damp / wet locations (note.10) high efficiency up to 94% features : h l g - 1 8 5 h s e r i e s ripple & noise (max.) note.2 voltage tolerance note.3 environment emi conduction & radiation safety & emc protection 100 10 (rth2) protection type : shut down o/p voltage, recovers automatically afte r temperature goes down en61347-1, en61347-2-13 independent approved ; design refer to ul6 0950-1, tuv en60950-1 ip65 or ip67 14 ~ 17v 18 ~ 21v 23 ~ 27v 28 ~ 34v 34 ~ 38v 41 ~ 46v 54 ~ 60v 47 ~ 53v 59 ~ 65v 91.5% 92% 93% 93.5% 93.5% 93.5% 94% 94% 94% 2.5% 6.5 ~ 13a 2.0% 5.75 ~ 11.5a 1.0% 4.65 ~ 9.3a 1.0% 3.9 ~ 7.8a 1.0% 3.1 ~ 6.2a 1.0% 2.6 ~ 5.2a 1.0% 1.95 ~ 3.9a 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 2.0% 1.5% 1.0% 0.5% 0.5% 0.5% 0.5% 1.0% 1.72 ~ 3.45a 0.5% 0.5% 1.0% 2.2 ~ 4.4a 0.5% 0.5% hlg-185h-12 hlg-185h-15 hlg-185h-20 hlg-185h-24 hlg-185h-30 hlg-185h-36 HLG-185H-48 12v 6 ~12v 15v 7.5 ~ 15v 20v 10 ~ 20v 24v 12 ~ 24v 30v 15 ~ 30v 36v 18 ~ 36v 48v 24 ~ 48v 13a 11.5a 9.3a 7.8a 6.2a 5.2a 3.9a 156w 172w 186w 187.2w 186w 187.2w 187.2w 150mvp-p 150mvp-p 13.5 ~ 17v 150mvp-p 17 ~ 22v 150mvp-p 22 ~ 27v 200mvp-p 27 ~ 33v 200mvp-p 33 ~ 40v 200mvp-p 43 ~ 53v 10.8 ~ 13.5v hlg-185h-54 54v 27 ~ 54v 3.45a 186.3w 200mvp-p 49 ~ 58v hlg-185h-42 42v 21 ~ 42v 4.4a 184.8w 200mvp-p 38 ~ 46v f m m 110 selv ip65 ip67 a : ip65 rated. output voltage and constant current level can be adjusted thr ough internal potential meter. b : ip67 rated. constant current level adjustable through output cable w ith 1~10vdc or 10v pwm signal or resistor. blank : ip67 rated. cable for i/o connection. 12v 15v ~ 54v short circuit constant current limiting, recovers automatically after fault con dition is removed protection type : shut down o/p voltage with auto-recovery or re-power o n to recovery
mechanical specification case no.994d unit:mm ip67 rated. cable for i/o connection. 300 20 300 20 fg (green/yellow) fg (green/yellow) sjtw 14awg(1.5mm ) 2c 2 sjtw 14awg(1.5mm ) 2c 2 38.8 sjtw 18awg(0.75mm ) 3c 2 sjtw 18awg(0.75mm ) 3c 2 228 228 204 204 ac/l(brown) ac/l(brown) ac/n(blue) ac/n(blue) 12 12 9.6 9.6 9.4 9.4 9.4 9.4 34.2 34.2 68 68 4.2 4pl 4.2 4pl 300 20 300 20 +v(red) +v(red) -v(black) -v(black) ip65 rated. output voltage and constant current level can be adjusted thr ough internal potential meter. (can access by removing the rubber stopper on the case.) 38.8 vo adj. io adj. 185w single output switching power supply h l g - 1 8 5 h s e r i e s a type:(hlg-185h-_a) blank:(hlg-185h) file name:hlg-185h-spec 2010-09-29
fosc : 100khz derating curve static characteristics ambient temperature ( ) load (%) -40 -25 -10 0 15 30 50 60 70 20 40 60 80 100 input voltage (v) 60hz 90 100 125 135 145 155 165 175 180 200 230 264 100 90 80 70 60 50 40 load (%) (horizontal) adj1 (b type) adj2 fosc : 100khz detection pwm & pfc circuit emi filter rectifiers power switching filter & rectifiers +v -v i/p fg control o.v.p. & o.l.p. pfc circuit block diagram 60k 60% 60% 10k 1v 4v 7v 2v 5v 8v 3v 6v 9v 10v 10% 10% 20k 20% 20% 30k 30% 30% 40k 40% 40% 50k 50% 50% 70k 70% 70% 80k 80% 80% 90k 100k open open open 90% 90% 100% 102%~108% 102%~108% 102%~108% 100% resistance value dimming value percentage of rated current percentage of rated current ip67 rated. output constant current level can be adjusted through outpu t cable by connecting a resistor or 1 ~ 10vdc or 10v pwm signal between adj1 and adj2. reference resistance value for output current adjustment (typical ) 1 ~ 10v dimming function for output current adjustment (typical) 60% 60% 10% 10% 20% 20% 30% 30% 40% 40% 50% 50% 70% 70% 80% 80% 90% 90% 100% 100% duty value percentage of rated current 10v pwm signal for output current adjustment (typical) 300 20 38.8 sjtw 18awg(0.75mm ) 3c 2 228 204 12 9.6 9.4 9.4 34.2 68 4.2 4pl 300 20 +v(red) adj1(blue) -v(black) adj2(white) fg (green/yellow) ac/l(brown) ac/n(blue) sjtw 18awg(0.75mm ) 2c 2 sjtw 14awg(1.5mm ) 2c 2 pfc control o.l.p. o.t.p. 185w single output switching power supply h l g - 1 8 5 h s e r i e s b type:(hlg-185h-_b) file name:hlg-185h-spec 2010-09-29
0 .8 4 0 .8 6 0 .8 8 0 .9 0 .9 2 0 .9 4 0 .9 6 0 .9 8 1 1 .0 2 5 0 % 6 0 % 7 0 % 8 0 % 9 0 % 1 0 0 % 2 3 0 v a c 1 1 0 v a c power factor characteristic power factor will be higher than 0.9 when output loading is 50% or higher. pf load constant current mode there are two major kinds of led drive method "direct drive" and "with led driv er". typical led power supply i-v curve a typical led power supply may either work in "constant voltage mode (cv) or c onstant current mode (cc)" to drive the leds. mean well's led power supply with cv+ cc characteristic can b e operated at both cv mode (with led driver, at area (a) and cc m ode (direct drive, at area (b). driving methods of led module efficiency vs load (48v model) hlg-185h series possess superior working efficiency that up to 94% can be r eached in field applications. load efficiency (%) 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 230vac 110vac efficiency vs load (48v model) hlg-185h series possess superior working efficiency that up to 94% can be r eached in field applications. load efficiency (%) vo(%) 100 50 50 100 io (%) constant voltage area constant current area (a) (b) 185w single output switching power supply h l g - 1 8 5 h s e r i e s file name:hlg-185h-spec 2010-09-29
direct driving : under direct driving, the power supply will work in "constant current mod e (cc)" and output voltage of the power supply will be clamped by sum of forward voltage (v ) of the led strip. f the total forward voltage of series connecting leds is suggested for 60%~ 95% of power supply rated output voltage due to concern of the best pf value and efficiency. ac source i/p o/p hlg-185h with led driver using additional driver, the power supply will work in "constant voltag e mode (cv)" and output voltage of the power supply will be kept in rated value. in this drive mode, several design issues need to be considered: 1.output voltage of psu must be higher than total forward voltage of series c onnecting leds by 3v minimum. 2.input capacitor (cin) of led driver circuit should use 47uf ~ 100uf(typ .) of rating depends on the operating frequency of the led driver. the higher the operating frequency is used, the smaller value of cin should b e chosen, and vice versa. ac source i/p o/p ic circuit cin cout v f r l hlg-185h ~ ~ ~ ~ 3.do not use b type with led driver. dimming connection diagram for turning the lighting fixture on/off : using a switch and relay can turn on/off the lighting fixture. using the built-in dimming function on b-type model can't turn the lighti ng fixture totally dark. please refer to the connection method below to achieve 0% brightness of the lighting fixture connecting to the led power s upply unit. 1.output constant current level can be adjusted through output cable by c onnecting a resistor or 1~10vdc or 10v pwm signal between adj1 and adj2. 2.the led lighting fixture can be turned on/off by the switch. n fg l led lighting relay blue brown green/ yellow ac/l ac/n hlg-185h b type adj1 adj2 v(-) v(+) blue(+) white(-) black red switch adjuster 0~100k ohms resistance 1~10v dc voltage 10v pwm signal dimming operation(for b-type only) 185w single output switching power supply h l g - 1 8 5 h s e r i e s file name:hlg-185h-spec 2010-09-29
waterproof connector waterproof connector can be assembled on the output cable of hlg-185h to op erate in dry/wet/damp or outdoor environment. hlg-185h i/p o/p led lamp ac source cable joiner pin configuration (female) pin configuration (female) size size m12 m15 4-pin 5a/pin m12-04 order no. order no. 10a max. suitable current suitable current 5-pin 5a/pin m12-05 10a max. 2-pin 12a/pin m15-02 12a max. up to four wires can be connected through this cable joiner bysoldering or clamping by tools. 66 26 20 25 suitable for 14awg~22awg o/p wires led lamp hlg-185h waterproof connection ~~ ac source i/p fg c b d a a o/p led cc driver chassis of led lamp cc ic hlg-185h a. add a common mode ferrite choke on output wires to reduce the common emissi on between 10m ~ 300mhz per lighting emi regulation. b. chassis of led lamp and chassis of hlg-185h or the fg wire should be connected t o the safety ground to reduce the emi noise, including the conduction and radiation emission. c. the additional x-cap and discharge resistor can reduce the l conduct ion noise between 9k ~ 1mhz per lighting emi regulation. d. l-c filter should be added at the dc input of led constant current driver to avo id the differential emission and high frequency noise generated by the cc driver. ow frequency emi debug suggestion 185w single output switching power supply h l g - 1 8 5 h s e r i e s file name:hlg-185h-spec 2010-09-29
|
